Table of Contents
If you are getting irritated by putting on the binding because many times you miss catching the back of the binding and get some gaps. So this article is for you. Never miss it, again and again, get incredibly straight stitching. So in this article we are presenting a guide for you to learn how to use the binding foot.
Do you forget about that box of sewing feet that I bought? We have been gradually working on it and getting varying degrees of success. After buying that I never get worried too much about the precision of my sewing. These binding foots are certainly benefitting me to get a great finish on all of my pieces. These binding foot are amazing and have been making up all types of little bits and pieces to add some binding onto.
Hence, have a look at how to use a binding foot!
Generally people have a foot fetish, that is also not a weird type of feet and are the sewing machine type of foot. Binding foot is a recent and modern addition that is also amazing. Binding foots can be used to attach bias tape and quilt binding. It’s a wonderful addition because it lines up the needle right where you want it and gets an amazing straight stitching! One of the most favorite parts of it is that whatever you are sewing you don’t have to pin the binding all the way around before you connect it. You just have to feed it into the binding foot as you feed the fabric in and voila!. You can use it for binding upto an one inch wide. The measuring scales are in millimeters. You just have to make an adjustment of the screw on the right side for a smaller tape.
Binding Foot Parts
- Binding edges( two little plastic tabs)
- Fabric placement part
- Adjusting screws.
Characteristics Of Binding Foot
The binding foots are made in a way that it can be adjusted so that it can deal with different widths of binding. Its workimng mechanism is with bias binding and its great for use around gentle curves and circles. The binding foot may also works with straight cut binding for straight edges too. After some practice you can use it to have clean mitered corners too_ once you have more practicing then you will learn more and will have a great sewing. For now we will assume that we have to add straight binding to a edge and it will do it in a single pass, sewing from frint and back at the same time incredibly.
You know there are two wheels on the foot. With one wheel you may adjust the position of the foot itself, you may slide it left or right and then another wheel will adjust the width of the clear part of the binding foot that have to hold the length of binding. These 2 wheels will control a sliding guide that runs along the length of the binding as you stitch and keeps it snugly in place against the guides for wonderful sewing.
The plastic parts of binding foot are flexible, especially when those lower wheel is turned to the wider setting so that they can be open up widely to allow the fabric and binding sandwich to be put together. Binding foot have number printed on it that will indicate the width of binding, but numbers are really not needed. Just turning that wheel I think using number for guide is more essential than unitil the binding is snug.
How To Load Binding And Fabrics On It?
There are two methods of binding which are :
First method of binding
With open edge feed in the binding tape on the left side and then fold on the right side. Then discrete the both open edges and slide from both up and down side edges under these little tabs on the left side of jaws. That is how it must look with fabric from top and bottom separated which are held by little plastic guides.
Regulate or maintain the bottom wheel until the guide moves over snugly to the folded edge of binding and this binding should place softly between the left and right edges and without crumpling. Now expose up the jaws with your fingers and slide in the fabric to be bound. Now push the edges right upto the fold of binding. Now just slip the foot and bind up to the initiation of the edges to be bound. Now you are all set for stitching.
2nd method of binding (whole sandwich method)
This method is most easy one but also depends on your preference. In this method instead of first loading the binding and then fabric after. I pinned the binding to the fabric and load it into foot all in one go. And move the guide over to the right so u can easily open up the jaw. Now when you are going to initiate pin or clip the binding with a gap of 3 to 4 inches between your pins, where you want to sew as it is ready to stich.
Now glide the foot in a place around whole sandwich means between those pins and edges of binding in the guides on the left. Ensure the forefront side and back side are lying in the glide properly and smoothly.
And now turn out the under side wheel to move the right hand guide snugly up against the folof the binding. Now its all ready to sew. Then start removin pins, firstly remove the top side pin, slide the foot back where you want to start sewing you are all set. As u start to sew remove the lower side pins. And this method is less fiddly by loading the whole sandwich at once.
How to use a binding foot?
There are 6 steps to use a binding foot.
- Keep the binding through the guides in the presser foot.
- You should use pins or clips to guide the binding in case if it gets stuck.
- Make adjustment of width of the guide by turning the dial until it gets same as binding width.
- Put the fabric through the gaps between the guides, line the edge of fabric up with the centre fold of binding.
- Now its time to attach binding foot to the sewing machine.
- Now regulate the needle position to close to the edge of binding.
- Start stitching and make sure the fabric edges stays at the fold of binding.
How To Stitch With binding Foot :
I make u sure that these binding foot will help you to have easy instant sewing. So make your sewing life easier and smooth.
Top Best Binding Foot
We have many goop options of binding foot available on amazon so lets have a look:
- Distinctive Tape Binding Presser Foot
- Kalevel Tape Binding Foot
- Amosfun Bias Tape Binding Binder Foot
Tips For Using Binding Foot
Here are some of vital tips of using binding foot:
- A plastic guide must be flexible to make it instant and easy to insert your mai n fabric.
- A flexible plastic guide will help you to expose the jaws a bit to help the fabric to be sewed.
- Its effortless to get the binding into accurate position with the foot off the sewing machine, then connect the foot when its all in position.
- If you are stitching binding to more tham one piece of fabric, when you have end up with sewing the first piece then pull up the fabric and bind it to the back and ensure the keeping of binding in the guides. It will be time saving.
- If you want to use decorative sewing mode for a fancier touch then you may.
- The binding foot would work great with woven binding.
You may do sewing perfectly any time with a pair of adjustable binding foot. In this precisely described guide we have show each and everything that how to use a binding foot for any kida fabric. Also we have mentioned some precious tips to for using binding foot. Additionally we have also described all of the wonderful features of binding foots. So that you may decide that either it will make your sewing life smooth or not.
Along with all these things we have also mentioned the top best binding foot that is readily available on Amazon. So you may check their price in the product link.
So lets enjoy your sewing life with adjustable binder foot!
I’m Victoria, and embroidery/sewing has been a part of my life since I was a little girl. My passion for this craft is what inspired me to start this blog to help passionate crafters choose the right craft tools. Whether you’re a beginner, intermediate, or professional sewer, there is something for everyone in this craft corner. Follow along my journey here.